BSBY_f009 ion blower brand [Shunguan] The factory adhering to the "quality of life, service is the key, faith is fundamental," the purpose of the trip will continue anti-static equipment enterprises to solve any difficulties encountered. In addition to electrostatic ion fan how much influence "ion fan on products and equipment ESD performance and give the same attention to pollution control, clean room garments and materials preferably with static dissipative materials, and can be grounded." Relevant industry people think so. Other industries, especially in the head drive industry, clean rooms with a more anti-static material. In the past, the magnetic head driving sector only of the IC (chip, micro-chip) used in the production ESD control. But now there are more industries using ESD control techniques. Because electrostatic discharge (ESD) for precision circuits, the impact of the disk, the electronics industry is facing enormous challenges. They will lose billions of dollars each year. Only 5V voltage may damage the tiny delicate component, the voltage is less than 100V may scrap the entire electronic circuit. In areas affected by ESD, clean room managers must take into account the production line caused by the ESD failure and damage percentages. However, ESD Control material and easy to cause pollution - static dissipative materials are cleanroom dust particles and a major source of chemical contamination. For ESD control, clean room items are made static dissipative material, to prevent ESD and electrostatic attraction. Select the appropriate anti-static clean room supplies ion blower is a big challenge. However, ESD solution than finding static dissipative materials more complicated. Therefore, experts recommend a set of ESD control procedures. Available technologies can be used in the clean room designed for the static dissipative products: cotton, cloth, glue, fabric, wall materials, wrist band, gloves, work clothes, etc. However, static dissipative materials may also cause pollution, a lot of plastic or stainless steel clean room products may accumulate or conduction electricity ESD products manufacturer for the development of new static dissipative material has a certain degree of difficulty. In the IC smaller, static sensitivity is also enhanced. Nearly three years, a lot of electronics manufacturers have begun to demand more ion fan ESD products. Finding the right anti-static materials have a certain degree of difficulty. Light board cover made of plastic, with a very good wear resistance, low volatiles and chemical resistance, good clean room for a material. To find the very transparency of the raw materials is difficult. Due to the presence of different additives and the refractive index of the copolymer composition of the material will become opaque. Moreover, the plastic must have a good surface resistance. Electrostatic adsorption in the clean room because of static electricity, so become more difficult to remove contamination. The role of dust particles due to electrostatic always easy to stick to the silicon wafer, resulting in damage to the product, excellent rate. Our biggest problem is to find a suitable clean room use anti-static material. In the LCD industry, the glass substrate becomes large, the ability to attract charge enhancement. Since the substrate is large in size, any contamination may result in optimal rate. And other pollution control industries, LCD industry has been looking for to solve the ESD problem new material. The materials used in the clean room are also more likely to use an anti-static ion fan, on the swabs and wipes can also try to find new materials to replace traditional materials. Why is clean room suitable type is not suitable for ESD products? Over the past 3-5 years, manufacturers have to provide products to clean room when using both recognize the need ESD cleanroom products. However, the clean room can be used to find an ESD products is a problem. Because a lot of products for cleanroom ESD performance is not stable enough. ESD Control in the clean room of the biggest challenges is the staff in the clean room to move around. Because a lot of people wearing polyester fabric, it will generate a lot of charge. In the clean room the only way to remove this charge is grounded. In the past five years, it was found mixed with carbon fibers and fabrics made work clothes system can provide for ISO5 (Class100) class clean room requirements. Such work clothes of all parts of the same conductivity, and from the hood to the soles of the feet are electrically connected. Working in the clean room staff to wear such clothes while walking through conductive sole ground rather than through the ground wire to ground, so not limit the length of the ground wire. The emergence of such work clothes is the result of high demand products to help reduce cleanroom ESD problems caused due to low yield and high defect rate. ESD ion fan control for quick repair method is not cheap, it is critical to ESD control, such as suspension laminar ion fan, or in the need to control the installation of ESD materials beside ion fan. With the chip (IC) size reduction, more and more sensitive to ESD. Now, ESD control work is not limited to the protection of the network, the need for wafer and wafer production control personnel. Many high standards of the company is such to ESD control. Clean room equipment research and development production and sales; purification engineering system design, construction, installation, commissioning and maintenance; BSBY network marketing ......