BSBY_f002 anti-static access control brand [cis crown, Miss Yang, 13580960057] company to honesty, credibility-oriented philosophy to provide our clients with the highest quality products, perfect service, many customers throughout the country and established a good business relationship, the majority of users to gain a good reputation! Installation electrostatic generator 1, the DC high voltage supply is fixed in position. 2, the electrostatic emitter (bar) in accordance with the actual work you need to install fixed. 3, with a separate ground wire to the grounding screw on the back of the high-voltage supply. 4, the electrostatic emitter (bar) high-voltage direct current high voltage supply plug into the output jack (two holes and let it choose one), and tighten the lock nut comes with a plug. 5, confirm that the power supply (mains) is consistent with the DC high voltage supply operating voltage, the high voltage power supply with grounded plug into a mains socket. 6, the DC supply power switch in the ON position, the switch lights. 7, the band switch in the "1" position (or 2,3,4 positions also available), the red indicator light, the output voltage shows "0", the DC high voltage supply enters the standby status. 8, the DC high voltage supply panel to directly control: Press the start button (START UP), and maintained for about 3 seconds. High voltage supply to trigger the start, the red light is off, the green light is on, the high voltage output value reached and exceeded undervoltage, high pressure supply into the self-locking state, release the start button. If you want to quit working (to stop high-voltage output), as long as the power switch in the "OFF" position. 9, the other host DC high voltage supply control work. The host must provide two sets of pressure is greater than 24V, 1mA current greater than allowed by the normally open contacts. Such as touch switches or micro hard-contact switches or soft PLC or relay contacts. Connection type "D" stick to the high pressure supply of the first "D" type socket. 4,5 termination socket stop contacts. 6,7 endpoint then start contacts. When activated, the contacts 6,7 connectivity to keep about 3 seconds. The high-voltage supply to trigger the start. Then the green light is on, the red light goes out. Supply of high-pressure and high-pressure output from the lock. When the high voltage supply to enter the self-locking state 6,7 contacts should quit connectivity, otherwise high voltage supply can not play short-circuit protection. If the high voltage supply to stop working, as long as 4,5 end connectivity, and holding time of about 5 seconds, the green light is off, the red light is on. High voltage supply to standby status. Here in particular is connected to start contacts 6,7 and 4,5 stop contacts should be without a touch of self-locking switch or micro switch, press and hold the hand that was connected, it will automatically let go after homing or disconnected. If you want to monitor the work of the high-pressure supply state, the status of their work on the host alarm by sound (or light). The host must provide a power of less than 220V and indicating device or alarm device and the power supply matches (such as red, green or buzzer). 1,2 point socket normally closed contact, that the high-pressure supply is working properly, the two contacts open when the output high voltage. These two points can be considered a red light and a buzzer connected. 2,3 normally open contact, that the high-pressure supply is working properly, the output of the two high-voltage contact closure, these two can consider taking green. Users can set up light or sound alerts (alarms) 1,2,3 contacts according to their own functions. 10, regulating the output voltage value: hand rotating band switch voltage regulator, the output voltage reaches the appropriate voltage value used. Company Name: Dongguan Shun crown Antistatic Equipment Co. electrostatic generator: http://www.esdyiqi.com http://www.lizifengqiang.net http://www.lizifengshe.com http://www.lizifengzui . com http://www.dglizifengji.com charge: Miss Yang Tel 0769 -85,998,131 0769-85998132 Mobile: 13580960057 15820839933 Fax 769 -85886353 E-mail: cs@shunguan.com.cn QQ: 317094843 Address: Dongguan, Guangdong Province Houjie Village, Houjie Town auspicious Road WAYAO Dun (LYM restaurant behind)